TV Installation
This guide is for installers setting up LG ProCentric TVs in guest rooms. Nothing is typed on the TV. Either the TV is registered in advance, or you scan the QR code it shows and choose the site and room on your phone.
Before you start
The hotel's TV head-end must point TVs at the ProCentric server below. This is done once for the whole hotel, not per TV.
| Head-end setting | Value |
|---|---|
| Server (host) | tv.provyl.com |
| Port | 80 |
| Protocol | HTTP |
TVs then load the application list from
http://tv.provyl.com/procentric/application/xait.xml by themselves. The
path is fixed by the TV firmware and is not entered anywhere. HTTP works on every
TV, including older models that cannot load it over HTTPS; TVs that support it
can use HTTPS on port 443 with the same server. Either way the guest app
itself opens over HTTPS.
The same address is shown in the Head-end card on the console's TV Manager β TVs screen.
You need a console account with the Devices area at the Operator role (or higher) for the hotel, and a phone.
Installing a TV
TVs registered in advance
If the TV's serial number was registered in TV Manager β TVs β Add TV with its room, just switch the TV on. It shows Setting up this TV while it applies the hotel settings, restarts if a setting needs it, and opens the guest app. Nothing else to do.
TVs that are not registered
- Switch the TV on. It loads the hotel TV app and shows Register this TV with a QR code and its serial number, model, and network address.
- Scan the QR code with your phone. It opens Add TV in the console with this TV already filled in. Sign in if asked. There is no code to type.
- Check the TV β the serial number on the phone matches the TV screen.
- Choose the site and the room from the list, then press Register TV.
- If the room already has a TV, a warning lists it: the TV is added to the room.
- A room that is not in the list: pick + New roomβ¦ and type its number β the room is created.
- Wait. Within a few seconds the TV shows Setting up this TV, applies the hotel settings, restarts if needed, and opens the guest app.
No camera? In the console open TV Manager β TVs β Add TV β Serial number on any phone or computer, enter the serial number shown on the TV screen, and choose the site and room. The TV picks this up while it shows the QR code and sets itself up the same way.
On a phone, Scan barcode next to the serial number reads the barcode next to S/N on the label on the back of the TV (or on its box) and fills the number in β useful for registering TVs in advance. If it reads another barcode, such as the model number, it says so and keeps looking.
The TV is now installed. It appears in TV Manager β TVs within about half a minute, shown as online. From now on the TV knows its own room: its QR code pairs phones with this room, and check-in and check-out from Rooms reach this TV. It starts in guest mode every time.
Moving a TV or installing it again
A TV comes back to the setup screen if its stored data was wiped (for example by a factory reset) or its registration was removed. Three ways to bring it back:
- On the TV, nothing to scan: an installed TV shows Reconnect this TV with its site and room. It connects by itself after 30 seconds β or press OK now, or choose another room of the same site. BACK shows the QR code instead. See A reset TV reconnects by itself.
- Same room, no phone needed: in TV Manager β TVs, pick Re-link in the TV's β― menu, then restart the TV app within 15 minutes. The TV reconnects to its room by itself. (Check-out does this automatically, so a TV that clears its data at check-out reconnects without help.)
- Any room: scan the QR code and register the TV again. Add TV shows where the TV is registered now; registering moves it to the room you choose.
What the setup applies
During setup the TV registers the app tokens the hotel uploaded (Netflix, Amazon, Google Cast β¦ β see Smart Apps), and also reads the apps it supports and reports them to the console β they appear in Content Manager β Watch β Apps (switched off until you turn them on). It does the same each time it starts. The setup screen logs this step; if it cannot report, setup still completes and tries again at the next start.
The settings come from TV Manager β TV Presets. By default: Full HD output, hidden channel banner, remote troubleshooting enabled, and the power mode that lets staff turn the screen off and on remotely. Output resolution and remote troubleshooting take effect after a restart, which the TV does by itself during setup.
Troubleshooting
"This QR code is no longer valid"
The QR code stays valid while the TV shows it. It changes when the TV restarts or has been off for more than ten minutes. Scan the QR code on the TV again.
The site or room I need is not in the list
The site list only shows sites where your account can operate Devices. Ask an administrator for access. Administrators for all sites can create a new site from the list (+ New siteβ¦).
"This TV was deactivated in the console"
Someone deactivated this TV. Scan the QR code and register it again to bring it back into service.
"Camera access is blocked"
Add TV reads the QR code with the phone's camera. Allow the camera for the site and reload the page:
- iPhone (Safari): tap aA in the address bar β Website Settings β Camera β Allow.
- Android (Chrome): tap the icon left of the address β Permissions β Camera β Allow.
Or scan the QR code with the phone's own camera app, or register the TV by its serial number.
"Setting failed: β¦"
The TV refused one of the settings. Setup continues and the TV is still registered. Note the setting name and report it.
"Restart failed. Please turn the TV off and on."
Turn the TV off and on at the wall. Everything else has already been done.
"Could not reach the server β retrying"
The TV cannot reach the internet. Check its network connection; the screen keeps retrying and shows the QR code once it is connected.
The TV shows the guest screen instead of the setup screen
Either the TV is already registered, or the TV app could not reach the TV's system functions. Check TV Manager β TVs: if the TV is listed there, it is registered.
The TV is installed but shows "Offline" in the console
Check the TV's network connection. A TV is shown online once it reports in, which happens every 30 seconds while the TV app is running.